Archgard 31-DVI33N Specifications download pdf (Page 17)

31-DVI33N 17

Instructions for use with Archgard vertical termination cap. Part # 999-INS-TK

Install the termination cap being sure to provide sufficient space (around and on top) so as not to

impede the flow of air, both into and out of the cap. This cap is only to be used for non combusti-

ble installations. Do not recess into the top of the chimney.

1. Mark each end of one liner with “Air Intake”.

2. Mark each end of the second liner with “Exhaust”.

3. Pull the liner through the chimney.

4. Install the flashing. Do Not bend or cut the flashing in any way.

5. Seal and attach the liner marked “Air Intake” to the vent terminal pipe marked “Air Intake” with the collar

clamp provided.

6. Seal and attach the liner marked “Exhaust” to the vent terminal pipe marked “Exhaust” with the collar clamp

provided.

7. Seal and attach the end of the flex marked “Air Intake” to the collar marked “Air Intake” on the appliance

with the collar clamp provided with the unit.

8. Install exhaust vent restrictors provided with the unit on Natural Gas appliances only. .

Seal and attach

the end of the flex marked “Exhaust” to the collar marked “Exhaust” on the appliance.

9. Caulk all joints using a high temperature sealant such as milpac. DO NOT USE SILICONE SEALANTS. Use

of silicon sealants voids the warranty of the pilot assembly.

NOTE: The vertical termination cap must be sealed to the liner with suitable high temperature sealant and with the

hose clamps fasteners provided. The liners must form a complete connection from the appliance

flue collars to the

vertical termination cap.

VENTING INSTRUCTIONS 999-INS-TK

The minimum flue (chimney) size required to run the two 3” (76 mm) is 4” x7” (100 mm X 178 mm)

Front view of

DV Insert

Exhaust

Collar

Exhaust

Air Intake

Collar

3” (76 mm)

Flex Liner

Fresh Air

Intake

Min. vent height 10’(2.54 M)

Max. vent height 40’ (12.2 M)

Vertical Termination cap

Part # 999-INS-TK

Place Vent Restrictor

in the position shown

when operating with

NATURAL GAS with a

vent over 18’ (5.5 Me-

ters)

Firebox baffle with

restrictor

Firebox baffle with-

out restrictor

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 45 46

31-DVI33N 1
INTRODUCTION 3
TABLE OF CONTENTS 4
31-DVI33N 5 5
31-DVI33N 6 6
31-DVI33N 7 7
31-DVI33N 8 8
31-DVI33N 9 9
31-DVI33N 10 10
31-DVI33N 11 11
31-DVI33N 12 12
CONVERSION KIT INSTRUCTIONS 13
31-DVI33N 14 14
31-DVI33N 15 15
31-DVI33N 16 16
31-DVI33N 17 17
31-DVI33N 18 18
31-DVI33N 19 19
31-DVI33N 20 20
31-DVI33N 21 21
31-DVI33N 22 22
31-DVI33N 23 23
31-DVI33N 24 24
31-DVI33N 25 25
31-DVI33N 26 26
31-DVI33N 27 27
31-DVI33N 28 28
31-DVI33N 29 29
31-DVI33N 30 30
31-DVI33N 31 31
31-DVI33N 32 32
31-DVI33N 33 33
31-DVI33N 34 34
31-DVI33N 35 35
31-DVI33N 36 36
31-DVI33N 37 37
31-DVI33N 38 38
WIRING SCHEMATICS 38
31-DVI33N 39 39
31-DVI33N 41 41
31-DVI33N 42 42
31-DVI33N 43 43
31-DVI33N 44 44
ARCHGARD INDUSTRIES LTD 45
Archgard Industries Ltd 46

Comments to this Manuals

No comments

Archgard 31-DVI33N Specifications Page 17

Comments to this Manuals

Related products and manuals for Fireplaces Archgard 31-DVI33N